Friday, August 25, 2017

QRP labs QCX 5 Watt cw trx kit


Here is my new winter project:  http://qrp-labs.com/qcx.html 
I couldn't resist buying this little 10 x 8 cm gem with a lot of features for just 49 $ 

The two SMD ICs are already factory pre-soldered.
Compleet unit size incl. spacers : 101.6mm x 81.3mm x 34mm.

A nice 110x88x38mm enclosure for this transceiver can be found on eBay : Link
The grooves for the pcb are not used and have to be reduced about 1mm near the volume potentiometer and the pcb pylons. Also the groove at the LCD side may touch the soldering pads of the LCD . The PCB is mounted on the original 12mm pylons. These pylons are held by countersunk headed bolts to the lower cover. So to open the enclosure, remove the two knobs and the upper 4 screws of the side panels. To prevent stress to the PCB , the huge plastic BNC connector is replaced by a metall chassis-mounted type. This will automatically ground the enclosure.😉
By means of a shaft extender the difference in height of the controls is matched.

AGC. Unfortunatly there is no agc on this transceiver. VK3YE designed an easy to install agc with a minimum of parts as you can see at Youtube : Easy AGC

 

 Removing the groove in the cover is verry easy. By carving into the alloy as the picture shows the material weakens and can be removed with a small srewdriver .


More info coming soon.

Monday, July 17, 2017

IC-7300 preselector idea.

The IC-7300 has a signal overload problem. A preselector can be an option.
L1 - T80-2 .  L2 - T68-6 .  L3 - T50-6 .  T1 - T2 are 1:9 transformers. By adding a 470pF capacitor to ground between T2 and the polyvaricon the overall swr drops to a verry acceptable levell.


Sunday, April 02, 2017

Voice keyer ( CQ parrot )

Calling cq in ssb with only 5 Watt can cause a sore throat....
Although in production for severall yaers this exellent kit BX-184 from Box 73 is still a must have for the QRP operator. Link
Easy to build high quality kit that provides 60 seconds voice recording and a strong punch to the modulation . I had to reduce the mic. gain to 25% on ssb and 15 % on fm/am at the FT-817.
This kit is also available with a extra MH-31 type mic. enabeling the use at other transceivers with 5V or more at the mic. cable. The red dot marks the fst button that controlles the functions,

The modified MH-31 mic.with pcb




Friday, January 20, 2017

EFHW antenna for 40-10m qrp

I had a BN43-202 core in stock and attempted to try to create a small QRP EFHW transformer from 7 - 29 MHz. As you can see in the plot the swr is verry flat from 40-10m so a capacitor at the input is not needed. A 3300 Ohm resister to ground was used for the plot but at 1700 Ohm the transformation is near perfect. Don't use thin antennawire for this rises the impedance of the antenna. 1.5mm is a minimum . With just 20.3m wire this makes a nice 40-10m antenna. You can also use the 34uH coil of the endfed down this blog to create a compact 3 band atenna of just 12m long. 10 Watts PEP is the max. power here. Be carefull, each pass is 1 turn here. A test with 2 transformers back to back showed a power loss of about 18% on 20m. I used 0.7mm transformer wire .




Disclaimer:I'm not responsable for any damage due to improper reproduction of my projects.

Translate